Furnace fans · ID, FD and high temperature · ISO 9001:2015 certified · Ahmedabad, IndiaFurnace fans · ID, FD and high temperature · ISO 9001:2015 certifiedGas up to 650 °C · built to your airflow and pressureMade in Ahmedabad · Quote within one working day

FD fans

Forced Draft (FD) Fans

Forced draft fans push combustion air into a furnace or boiler in the volume the fuel needs. Backward curved FD fans with belt or direct drive from AS Engineers.

  • ISO 9001:2015 · TÜV certified
  • 25+ years · 3000+ customers
  • Engineered to your process

Forced draft fans

The fan that puts the right amount of air into the fire

A forced draft (FD) fan pushes combustion air into the furnace or boiler through the burners or grate. The fuel needs a certain volume of air to burn fully. Too little and the fuel burns badly and makes smoke. Too much and heat is carried away up the stack.

The air is clean and near ambient temperature, so an FD fan is usually a simpler build than an ID fan. AS Engineers builds them as backward curved centrifugal fans with belt or direct drive, sized to your airflow and pressure.

  • Backward curved impeller for efficient running
  • Belt-driven or direct-coupled, standard drive arrangements
  • Variable frequency drive or inlet control for load changes

ID fan vs FD fan

Which fan does what?

A furnace normally has both. They do different jobs and are built differently.

Forced draft (FD) fanInduced draft (ID) fan
PositionBefore the furnaceAfter the furnace
HandlesClean combustion airHot, often dusty flue gas
Pressure effectRaises pressure in the furnaceLowers pressure in the furnace (draught)
Main concernAir volume to match the fuelTemperature, dust and corrosion
Typical impellerBackward curvedBackward curved or radial blade, by dust load
MaterialUsually mild steelChosen from the gas temperature and composition

Range

The range our centrifugal fans cover

These are the stated ranges of the AS Engineers centrifugal fan and blower range. Your own duty point decides the actual fan.

ParameterRange
Airflow100 to 2,50,000 m³/hr (design up to 3,50,000 m³/hr)
Static pressure25 to 2,100 mmWC
Motor power0.5 to 500 HP
Impeller diameter250 to 2,200 mm
Fan speed300 to 4,500 RPM
Operating temperatureAmbient up to 650 °C
Performance testingIS 4894 (BIS)
Dynamic balancingISO 1940-1, Grade G6.3 / G2.5
Quality systemISO 9001:2015 certified

Fan parts

What is inside a furnace fan

Each part has one job. A fan lasts when all of them are chosen for the same gas and the same temperature.

1Impeller

The wheel that moves the gas. Backward curved blades give a non-overloading power curve and good efficiency. Radial blades suit dirty or sticky gas.

2Casing and inlet

The scroll casing guides the gas to the outlet. Single inlet (SWSI) or double inlet (DWDI) construction is chosen from the airflow.

3Shaft, bearings and seal

Fixed and floating bearings take the thermal growth. Stuffing box or mechanical seal keep hot gas inside the casing.

4Cooling arrangement

Shaft cooler, cooling disc and an insulated pedestal keep the bearing temperature down when the gas is hot.

5Material of construction

Mild steel, carbon steel, stainless steel grades or duplex, chosen from the gas temperature and how corrosive or abrasive it is.

6Drive

Belt-driven or direct-coupled, in the standard drive arrangements. A separated pedestal design is used at high temperature.

7Expansion bellows and dampers

Bellows take up duct expansion so hot ducting does not load the fan. Inlet vane or damper control the airflow.

8Controls

Starter or variable frequency drive, and vibration and temperature sensors for safe, stable running.

Before we quote

Six facts we need to select your fan

Do not worry if you do not have all of them. Send what you know, and our engineers will ask for the rest.

1Gas

Hot air, flue gas or process gas, with its composition if it is corrosive, wet or dusty.

2Temperature

Normal and peak gas temperature at the fan inlet.

3Airflow

Volume in m3/hr or Nm3/hr, and whether it is at actual or normal conditions.

4Pressure

Static pressure the fan must develop, or the duct and furnace resistance.

5Duty

Induced draft, forced draft or recirculation, number of fans, standby needs.

6Site

Power supply, space limits, a layout sketch, fuel and any CPCB or safety requirements.

FAQ

Technical questions

What gas temperature can your fans handle?

Our centrifugal fan range covers operating temperatures from ambient up to 650 °C. The material and construction change with temperature: mild steel at lower temperatures, then SS 304, SS 321 and SS 310 as the gas gets hotter. Duties above 500 °C are reviewed one by one.

What gas temperature can your fans handle?

Our centrifugal fan range covers operating temperatures from ambient up to 650 °C. The material and construction change with temperature: mild steel at lower temperatures, then SS 304, SS 321 and SS 310 as the gas gets hotter. Duties above 500 °C are reviewed one by one.

What airflow and pressure range do you cover?

Airflow from 100 to 2,50,000 m³/hr, with designs up to 3,50,000 m³/hr, and static pressure from 25 to 2,100 mmWC. The motor range is 0.5 to 500 HP and the impeller diameter 250 to 2,200 mm.

What airflow and pressure range do you cover?

Airflow from 100 to 2,50,000 m³/hr, with designs up to 3,50,000 m³/hr, and static pressure from 25 to 2,100 mmWC. The motor range is 0.5 to 500 HP and the impeller diameter 250 to 2,200 mm.

What is the difference between backward curved and radial blade impellers?

A backward curved impeller gives good efficiency and a power curve that does not overload the motor, so it is the usual choice for clean or lightly dusty gas. A radial blade impeller is a sturdier shape that suits dusty, dirty or sticky gas and high pressure duty.

What is the difference between backward curved and radial blade impellers?

A backward curved impeller gives good efficiency and a power curve that does not overload the motor, so it is the usual choice for clean or lightly dusty gas. A radial blade impeller is a sturdier shape that suits dusty, dirty or sticky gas and high pressure duty.

Need an FD fan?

Send the fuel, burner or grate type, airflow and pressure. We reply within one working day.

Request your free quote

Step 1 of 2 · takes 30 seconds
What do you need?

Airflow, if you know it (m³/hr)

No spam · reply within one working day

Where should we send your proposal?

Prefer to talk? +91 99090 33851 · WhatsApp

Ready when you are

Dry smarter. Haul less. Save more.

Tell us your gas, temperature and airflow. We reply with a fan recommendation within one working day.

[ase_paddle_divider]
Chat with us
Secure form

Get your fan quote

Step 1 of 2 · takes 30 seconds
What do you need?

Airflow, if you know it (m³/hr)

No spam · reply within one working day

Where should we send your proposal?

Prefer to talk? +91 99090 33851 · WhatsApp

SSL-encrypted. Your details go only to our engineers – never shared or sold.