1Gas
Hot air, flue gas or process gas, with its composition if it is corrosive, wet or dusty.
Materials
Which material for which gas temperature: mild steel, SS 304, SS 321, SS 310 and alloys from ambient to 650 °C, with bearing cooling and what changes as the gas gets hotter.
Temperature and material
AS Engineers builds fans for gas from ambient up to 650 °C. The hotter the gas, the more the material, bearing arrangement and cooling matter.
| Gas temperature | Typical material | Notes |
|---|---|---|
| Up to 150 °C | Mild steel | Standard construction |
| 150 to 250 °C | Mild steel or SS 304 | Choice depends on the gas and how corrosive it is |
| 250 to 350 °C | Mild steel, SS 304 or SS 321 | Separated pedestal design is used above about 300 °C |
| 350 to 500 °C | SS 321 or SS 310 | Shaft cooler and insulated pedestal |
| 500 to 650 °C | SS 310 or a high temperature alloy | Every duty is reviewed individually |
These are typical choices. The final choice depends on the gas composition, how corrosive or abrasive it is, and whether the temperature is steady or cycles.
Materials we build in
The material is chosen from the gas temperature, the gas composition and the dust it carries.
The usual choice for cooler, clean gas. Carbon steel to SA516 Gr.70 is available for pressure duty.
SS 304 and 304L, SS 316 and 316L for corrosive gas, SS 321 and SS 310 for higher temperature, SS 410 and duplex 2205 where strength or corrosion resistance asks for it.
Blade leading edges can be hard faced where the gas carries abrasive dust.
Available for lighter duty on cooler gas.
Before we quote
Do not worry if you do not have all of them. Send what you know, and our engineers will ask for the rest.
Hot air, flue gas or process gas, with its composition if it is corrosive, wet or dusty.
Normal and peak gas temperature at the fan inlet.
Volume in m3/hr or Nm3/hr, and whether it is at actual or normal conditions.
Static pressure the fan must develop, or the duct and furnace resistance.
Induced draft, forced draft or recirculation, number of fans, standby needs.
Power supply, space limits, a layout sketch, fuel and any CPCB or safety requirements.
FAQ
Our centrifugal fan range covers operating temperatures from ambient up to 650 °C. The material and construction change with temperature: mild steel at lower temperatures, then SS 304, SS 321 and SS 310 as the gas gets hotter. Duties above 500 °C are reviewed one by one.
Our centrifugal fan range covers operating temperatures from ambient up to 650 °C. The material and construction change with temperature: mild steel at lower temperatures, then SS 304, SS 321 and SS 310 as the gas gets hotter. Duties above 500 °C are reviewed one by one.
Airflow from 100 to 2,50,000 m³/hr, with designs up to 3,50,000 m³/hr, and static pressure from 25 to 2,100 mmWC. The motor range is 0.5 to 500 HP and the impeller diameter 250 to 2,200 mm.
Airflow from 100 to 2,50,000 m³/hr, with designs up to 3,50,000 m³/hr, and static pressure from 25 to 2,100 mmWC. The motor range is 0.5 to 500 HP and the impeller diameter 250 to 2,200 mm.
A backward curved impeller gives good efficiency and a power curve that does not overload the motor, so it is the usual choice for clean or lightly dusty gas. A radial blade impeller is a sturdier shape that suits dusty, dirty or sticky gas and high pressure duty.
A backward curved impeller gives good efficiency and a power curve that does not overload the motor, so it is the usual choice for clean or lightly dusty gas. A radial blade impeller is a sturdier shape that suits dusty, dirty or sticky gas and high pressure duty.
Send the gas, its temperature and what is in it. We tell you what we would build the fan from, and why.