1Gas
Hot air, flue gas or process gas, with its composition if it is corrosive, wet or dusty.
Hot gas
High temperature plug fans for furnaces, ovens, kilns and hot gas recirculation. Shaft cooler, cooling disc and insulated pedestal, with materials chosen for gas to 650 °C.
High temperature fans
When the gas is hot, an ordinary fan fails: the shaft heats the bearings, the impeller loses strength and the casing grows. A high temperature fan is built to handle that, with the right metal, a bearing arrangement that allows for growth and a way of keeping heat away from the bearings.
AS Engineers builds high temperature plug fans as single inlet or double inlet fans, with shaft coolers, cooling discs, insulated pedestals and expansion bellows where the duty needs them.
Temperature and material
AS Engineers builds fans for gas from ambient up to 650 °C. The hotter the gas, the more the material, bearing arrangement and cooling matter.
| Gas temperature | Typical material | Notes |
|---|---|---|
| Up to 150 °C | Mild steel | Standard construction |
| 150 to 250 °C | Mild steel or SS 304 | Choice depends on the gas and how corrosive it is |
| 250 to 350 °C | Mild steel, SS 304 or SS 321 | Separated pedestal design is used above about 300 °C |
| 350 to 500 °C | SS 321 or SS 310 | Shaft cooler and insulated pedestal |
| 500 to 650 °C | SS 310 or a high temperature alloy | Every duty is reviewed individually |
These are typical choices. The final choice depends on the gas composition, how corrosive or abrasive it is, and whether the temperature is steady or cycles.
Built for heat
A shaft cooler, a cooling disc and an insulated pedestal keep the heat away from the bearings. Above about 300 °C a separated pedestal design is used.
Fixed and floating bearings and expansion bellows let the parts grow without loading the fan or the duct.
Stuffing box or mechanical seal keep hot gas in. High temperature grease is used where the bearing stays warm.
Hot gas volume calculator
Hot gas takes up more room. Enter the flow at normal conditions and the gas temperature, and see the actual volume the fan has to move and the material usually used at that temperature.
*Indicative only. Actual volume = normal volume × (273 + gas temperature) ÷ 273, at the same pressure. Real selection also depends on gas density and composition, altitude, duct resistance and the fan curve, so we size every fan from your duty data.
Before we quote
Do not worry if you do not have all of them. Send what you know, and our engineers will ask for the rest.
Hot air, flue gas or process gas, with its composition if it is corrosive, wet or dusty.
Normal and peak gas temperature at the fan inlet.
Volume in m3/hr or Nm3/hr, and whether it is at actual or normal conditions.
Static pressure the fan must develop, or the duct and furnace resistance.
Induced draft, forced draft or recirculation, number of fans, standby needs.
Power supply, space limits, a layout sketch, fuel and any CPCB or safety requirements.
FAQ
Our centrifugal fan range covers operating temperatures from ambient up to 650 °C. The material and construction change with temperature: mild steel at lower temperatures, then SS 304, SS 321 and SS 310 as the gas gets hotter. Duties above 500 °C are reviewed one by one.
Our centrifugal fan range covers operating temperatures from ambient up to 650 °C. The material and construction change with temperature: mild steel at lower temperatures, then SS 304, SS 321 and SS 310 as the gas gets hotter. Duties above 500 °C are reviewed one by one.
Airflow from 100 to 2,50,000 m³/hr, with designs up to 3,50,000 m³/hr, and static pressure from 25 to 2,100 mmWC. The motor range is 0.5 to 500 HP and the impeller diameter 250 to 2,200 mm.
Airflow from 100 to 2,50,000 m³/hr, with designs up to 3,50,000 m³/hr, and static pressure from 25 to 2,100 mmWC. The motor range is 0.5 to 500 HP and the impeller diameter 250 to 2,200 mm.
A backward curved impeller gives good efficiency and a power curve that does not overload the motor, so it is the usual choice for clean or lightly dusty gas. A radial blade impeller is a sturdier shape that suits dusty, dirty or sticky gas and high pressure duty.
A backward curved impeller gives good efficiency and a power curve that does not overload the motor, so it is the usual choice for clean or lightly dusty gas. A radial blade impeller is a sturdier shape that suits dusty, dirty or sticky gas and high pressure duty.
A shaft cooler and a cooling disc carry heat away from the shaft, and an insulated pedestal keeps the bearings cooler. At higher temperature a separated pedestal design is used, with fixed and floating bearings so the parts can grow, and expansion bellows in the duct.
A shaft cooler and a cooling disc carry heat away from the shaft, and an insulated pedestal keeps the bearings cooler. At higher temperature a separated pedestal design is used, with fixed and floating bearings so the parts can grow, and expansion bellows in the duct.
Send the gas, the normal and peak temperature, and the airflow. We tell you plainly what we recommend.